deleted old robot setup instructions file
This commit is contained in:
parent
c31c674ab2
commit
8b4e80d15e
|
|
@ -1,209 +0,0 @@
|
||||||
# Robot setup
|
|
||||||
|
|
||||||
This file explains how to setup the software for the robots. It assumes that you already assembled your robot according to the instructions in 1_ASSEMBLY.md
|
|
||||||
|
|
||||||
1 Install esptool
|
|
||||||
-----------------
|
|
||||||
The chip on the Wemos D1 mini is a Esp8266. In order to flash programs on this chip we will use esptool by Espressif.
|
|
||||||
You can install it using pip:
|
|
||||||
```
|
|
||||||
$ pip install esptool
|
|
||||||
```
|
|
||||||
|
|
||||||
2 Update Motor shield firmware
|
|
||||||
----------------------------
|
|
||||||
The Wemos motor shield comes with a buggy firmware which has problems with the I2C communication ([see here]([buggy firmware](https://hackaday.io/project/18439-motor-shield-reprogramming))).
|
|
||||||
Luckily, some guys figured out how to update the firmware of the STM32 on the motor shield with a custom one that fixes these issues.
|
|
||||||
|
|
||||||
These are the necessary steps:
|
|
||||||
#### Install arm compiler:
|
|
||||||
```
|
|
||||||
$ sudo add-apt-repository ppa:team-gcc-arm-embedded/ppa
|
|
||||||
$ sudo apt-get update
|
|
||||||
$ sudo apt-get install gcc-arm-embedded
|
|
||||||
```
|
|
||||||
|
|
||||||
#### Build the firmware:
|
|
||||||
|
|
||||||
Get the firmware from: [https://github.com/pbugalski/wemos_motor_shield](https://github.com/pbugalski/wemos_motor_shield)
|
|
||||||
```
|
|
||||||
$ make
|
|
||||||
```
|
|
||||||
-> motor_shield.bin
|
|
||||||
|
|
||||||
#### Upload empty firmware to Wemos D1 mini
|
|
||||||
We will program the STM32 on the motor shield using the serial USB connection from the Wemos D1 mini. The D1 mini should
|
|
||||||
just pass through the serial communication to the STM32. For this we need to upload a dummy firmware to the D1 mini.
|
|
||||||
|
|
||||||
1. Make sure the RTS and 3V port of the Wemos motor shield are connected by a wire (you should already have done this in the assembly instructions).
|
|
||||||
Also make sure that the I2C bridge connection on the motor shield is set.
|
|
||||||
|
|
||||||
2. Plug the Wemos D1 mini on top of the motor shield and then connect it to your PC using a micro USB cable
|
|
||||||
|
|
||||||
3. Compile the sketch below into a .bin file using the Arduino IDE -> `dummy_sketch.ino.d1_mini.bin` or use the one from `bin/dummy_sketch.ino.d1_min.bin`
|
|
||||||
|
|
||||||
Note: If you you compile it yourself make sure you choose the Wemos D1 mini board as target for the build.
|
|
||||||
|
|
||||||
```
|
|
||||||
void setup() {
|
|
||||||
// just some dummy code
|
|
||||||
}
|
|
||||||
|
|
||||||
void loop() {
|
|
||||||
// just some dummy code
|
|
||||||
}
|
|
||||||
```
|
|
||||||
4. Erase flash on the chip:
|
|
||||||
```
|
|
||||||
$ esptool.py --port /dev/ttyUSB0 erase_flash
|
|
||||||
```
|
|
||||||
5. Flash the dummy sketch:
|
|
||||||
```
|
|
||||||
$ esptool.py --port /dev/ttyUSB0 --baud 460800 write_flash --flash_size=detect 0 dummy_sketch.ino.d1_mini.bin/dummy_sketch.ino.d1_mini.bin.ino.d1_mini.bin
|
|
||||||
```
|
|
||||||
|
|
||||||
#### Install stm32flash utility:
|
|
||||||
To upload a new firmware to the STM32 that is running on the motor shield we need the STM32 flash utility.
|
|
||||||
You can download from: [https://sourceforge.net/projects/stm32flash/files/](https://sourceforge.net/projects/stm32flash/files/)
|
|
||||||
You should then build and install it using the usual:
|
|
||||||
```
|
|
||||||
$ make
|
|
||||||
$ make install
|
|
||||||
```
|
|
||||||
|
|
||||||
#### Connect the motor shield to D1 mini:
|
|
||||||
Use some jumper cables to connect the motor shield and the D1 mini in the following way.
|
|
||||||
|
|
||||||
|Wemos D1 mini | Motor shield|
|
|
||||||
|--------------|---------------|
|
|
||||||
|TX | D1|
|
|
||||||
|RX | D2|
|
|
||||||
|3V | 3V|
|
|
||||||
|GND | GND |
|
|
||||||
|
|
||||||
In addition on the motor shield connect 3V to RTS
|
|
||||||
Also make sure that the I2C bridge connection on the motor shield is set.
|
|
||||||
|
|
||||||
Then, connect the D1 mini to your PC using a micro USB cable.
|
|
||||||
|
|
||||||
#### Flash the new firmware on the STM32:
|
|
||||||
1. Check if you can communicate with the STM32:
|
|
||||||
```
|
|
||||||
$ stm32flash /dev/ttyUSB0
|
|
||||||
```
|
|
||||||
|
|
||||||
Output should be:
|
|
||||||
```
|
|
||||||
Interface serial_posix: 57600 8E1
|
|
||||||
Version : 0x31
|
|
||||||
Option 1 : 0x00
|
|
||||||
Option 2 : 0x00
|
|
||||||
Device ID : 0x0444 (STM32F03xx4/6)
|
|
||||||
- RAM : 4KiB (2048b reserved by bootloader)
|
|
||||||
- Flash : 32KiB (size first sector: 4x1024)
|
|
||||||
- Option RAM : 16b
|
|
||||||
- System RAM : 3KiB
|
|
||||||
```
|
|
||||||
|
|
||||||
2. Unlock shield:
|
|
||||||
```
|
|
||||||
$ stm32flash -k /dev/ttyUSB0
|
|
||||||
```
|
|
||||||
|
|
||||||
Output should be:
|
|
||||||
```
|
|
||||||
stm32flash 0.5
|
|
||||||
|
|
||||||
http://stm32flash.sourceforge.net/
|
|
||||||
|
|
||||||
Interface serial_posix: 57600 8E1
|
|
||||||
Version : 0x31
|
|
||||||
Option 1 : 0x00
|
|
||||||
Option 2 : 0x00
|
|
||||||
Device ID : 0x0444 (STM32F03xx4/6)
|
|
||||||
- RAM : 4KiB (2048b reserved by bootloader)
|
|
||||||
- Flash : 32KiB (size first sector: 4x1024)
|
|
||||||
- Option RAM : 16b
|
|
||||||
- System RAM : 3KiB
|
|
||||||
Read-UnProtecting flash
|
|
||||||
Done.
|
|
||||||
```
|
|
||||||
|
|
||||||
3. Flash new motor driver:
|
|
||||||
```
|
|
||||||
$ stm32flash -f -v -w motor_shield.bin /dev/ttyUSB0
|
|
||||||
```
|
|
||||||
|
|
||||||
Output should be:
|
|
||||||
```
|
|
||||||
stm32flash 0.5
|
|
||||||
|
|
||||||
http://stm32flash.sourceforge.net/
|
|
||||||
|
|
||||||
Using Parser : Raw BINARY
|
|
||||||
Interface serial_posix: 57600 8E1
|
|
||||||
Version : 0x31
|
|
||||||
Option 1 : 0x00
|
|
||||||
Option 2 : 0x00
|
|
||||||
Device ID : 0x0444 (STM32F03xx4/6)
|
|
||||||
- RAM : 4KiB (2048b reserved by bootloader)
|
|
||||||
- Flash : 32KiB (size first sector: 4x1024)
|
|
||||||
- Option RAM : 16b
|
|
||||||
- System RAM : 3KiB
|
|
||||||
Write to memory
|
|
||||||
Erasing memory
|
|
||||||
Wrote and verified address 0x08000be8 (100.00%) Done.
|
|
||||||
```
|
|
||||||
|
|
||||||
#### Cleaning up
|
|
||||||
Finally, you can remove the wire between RTS and 3V.
|
|
||||||
At this point, please make sure that the I2C bridge on the Wemos Motor shield is connected. This is necessary for I2C to work correctly.
|
|
||||||
|
|
||||||
|
|
||||||
Flash Micropython to the Wemos D1 mini
|
|
||||||
--------------------------------------
|
|
||||||
The next step is to flash the micropython firmware to
|
|
||||||
```
|
|
||||||
$ esptool.py --port /dev/ttyUSB0 erase_flash
|
|
||||||
$ esptool.py --port /dev/ttyUSB0 --baud 460800 write_flash --flash_size=detect 0 esp8266-20190125-v1.10.bin
|
|
||||||
```
|
|
||||||
Setting up webrepl:
|
|
||||||
Connect using picocom:
|
|
||||||
```
|
|
||||||
$ picocom /dev/ttyUSB0 -b115200
|
|
||||||
```
|
|
||||||
3. Connect via picocom and enable Webrepl
|
|
||||||
```
|
|
||||||
>>> import webrepl_setup
|
|
||||||
```
|
|
||||||
-> enable, set password and reboot
|
|
||||||
|
|
||||||
Connect to local wifi:
|
|
||||||
```
|
|
||||||
>>> import network
|
|
||||||
>>> sta_if = network.WLAN(network.STA_IF)
|
|
||||||
>>> sta_if.active(True)
|
|
||||||
>>> sta_if.connect("<SSID>", "<PW>")
|
|
||||||
>>> sta_if.ifconfig() # this prints the IP
|
|
||||||
```
|
|
||||||
Use access point to connect:
|
|
||||||
```
|
|
||||||
>>> import network
|
|
||||||
>>> ap_if = network.WLAN(network.AP_IF)
|
|
||||||
>>> ap_if.active(True)
|
|
||||||
>>> ap_if.ifconfig() # this prints the IP
|
|
||||||
```
|
|
||||||
Default password for the access point: `micropythoN`
|
|
||||||
|
|
||||||
Connect via [online WebREPL](http://micropython.org/webrepl):
|
|
||||||
- Enter IP from above and click connect. Login with password.
|
|
||||||
- Upload boot.py via Webrepl to automatically connect to wifi and start webrepl after reboot
|
|
||||||
- You can also upload a file called main.py or just work in the webrepl terminal.
|
|
||||||
|
|
||||||
|
|
||||||
4. Connect via webpage and upload boot.py, main.py, etc.
|
|
||||||
Modify boot.py before uploading!
|
|
||||||
|
|
||||||
5. Connect to the robot and test the connection
|
|
||||||
|
|
||||||
The next step is to setup the position detection using ROS. For this see the ROS_SETUP.txt
|
|
||||||
Loading…
Reference in New Issue
Block a user